Parts & Accessories

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

Make it more aerodynamic – this nipple is hidden inside the rim. DT Hidden Nipples are designed for high-profile rims, in which the inverted design is essential for optimum precision. They are very light and hidden on the inside of the rim: perfectly suited for high aero wheels. The nipples will align perfectly due to their spherical contact surface. - Weight: 22g for 64 nipples

Maximum stiffness and highest safety—the RWS Quick Release for road and MTB. Our patented RWS axle system is stiffer, safer, and easier to use than conventional quick-release axles. The RWS quick release is absolutely reliable and offers a strong connection to the frame. The perfect choice for anyone who is looking for maximum performance and safety.

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Freehub bodies for Zipp Cognition hubs.

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

• 5mm skewer set (F+R hubs) • Standard 5mm Hex release • Black or Silver anodized finish • Chromoly axles

• Replacement aluminum quick release skewers

- Variable widths - Left: 35mm - Center: 52mm - Right: 39mm - Length: 126mm - Overall: 147mm

- Supplies full wheel illumination for 700c/29in wheels and smaller - Approximately 40 hrs of battery life - Water resistant design - Includes 3 (AA) batteries - Sold individually (1 wheel) - Easy to install

- For square taper and flanged. - Fits most cartridge BBs - Shell: 8mm Flanged axle bolt

Replace the loop that goes around your left chainstay to secure your coaster brake arm with this Sunlite replacement part. It's made of full stainless steel, and it includes a nylock nut, washer, and bolt.

- Fits all freewheel hubs - Will not fit Cassette hubs - Type: STD Plastic - Color: Clear

Replacement clear plastic spoke guard.

- Grade 3 balls and magnetite rust proof finish - Abec 5 precision and silicone w seals - 3 times cryogenic race treatment - Bearings sold individually, not as pair

- Flanged 15mm axle nuts - Durable chromoly construction - Spacing / Axle: B/O

WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 34mm

- AL6061 alloy tubeless Presta valve - Includes 2 O-rings, one standard profile and one aero profile, for an airtight seal on any rim - Removable valve core for installing sealant - Additional replacement valve cores sold separately - Sold individually

Origin-8's Torq Lite Track Cog Lock Ring 1.29" x 24 tpi with left-handed threaded thread is the only lock ring you need. Hardened threading and extra material make this highly durable to help you go the distance.

Heavy duty and extra wide PVC rim strips for maximum tube protection.

Replacement freehub spoke protector, in various sizes for different freehub sizes. - Made of clear plastic - 3 hooks for affixing to spokes

- High-quality fat bike rim strips - Super durable PVC material

- Green colored spoke prep remains pliable for adjustments - Helps keep spoke nipples from loosening

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 174mm - 1 axle per bag

- Colored rim decal kits to personalize your ride - Decals to fit 2 100w 26-inch rims

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 50w 27.5+ rims

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 70w 26-inch rims

Ultra-light, bolt-on thru-axles, with a low-profile 6mm head for use on Whisky forks and others. They are also available in some common rear frame sizes. See manufacturer's specifications for fitment questions. - Thread Length: 12mm

Surly Ultra New Axle Kits are for upgrading the internals of your existing Surly New hubs or replacing the internals on your Surly Ultra New hubs. -Compatible with Surly New hubs (upgrade kit) and Surly Ultra New hubs (replacement kit) - Each kit contains an axle, two 6901 cartridge bearings, two aluminum dust shields, two stainless steel cones, two stainless steel 6x1mm bolts, and two stainless steel bolt washers - Axle is quick release and bolt-on compatible; bolts included, QR is NOT included - Standard Surly New hubs come stock with 7901 bearings; this kit uses 6901 bearings which are non-angular

Surly Thru-Axles are low-profile, bolted Thru-Axles are specifically designed for use with Surly thru-axle compatible frames. Offered in several sizes, for both front and rear wheels. 12x142 Rear Thru Axle: - Fits: Midnight Special and MDS Dropout bikes including Instigator, Legacy Karate Monkey & Legacy Krampus. 12x142/148 Rear Thru Axle: - Designed for frames with Surly Gnot Boost spacing (145mm), capable of working with 142 or 148mm rear hubs - Fits: Karate Monkey, Krampus, Troll, Ogre, ECR 12x177 Rear Thru Axle: - Fits: Wednesday 12x197 Rear Thru Axle: - Fits: Ice Cream Truck, Big Fat Dummy 12x100 Front Thru Axle: - Fits: Midnight Special 15x110 Front Thru Axle: - Fits: Karate Monkey, Krampus 15x150 Front Thru Axle: - Fits: Wednesday, Ice Cream Truck, Big Fat Dummy

Wheels Manufacturing Axle Spacers help you dial in your hub spacing to ensure correct fit and side-to-side spacing in the rear triangle without having to alter the wheel's dish. - Spacers come in bags of 20

Pro Head Reinforcement System (PHR) has a larger and more spherical contact area and is designed to balance loads transferred to the rim. The PHR system acts as a ball and socket interface, allowing the spoke to pivot into alignment while maintaining even, consistent contact during installation in order to follow the perfect trajectory from the hub to the rim.

When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Removable, plug-in lever design is streamlined and protects your RWS lever

- Flanged 15mm axle nuts - Durable chromoly construction - Spacing / Axle: B/O

WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs. - End Cap Included

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

The Trace rear axle fits Race Face wheels equipped with Trace hubs, like the Aeffect Wheelset. Use it as a replacement axle or to convert your wheel to a different axle standard. - Light and strong alloy construction - Compatible with Race Face Trace hub

Seal kit to keep water and dirt out of your Race Face Vault hubs.

Convert your ISO, ISO B, or ISO Superboost DH rear hub to a Shimano Micro Spline compatible driveshell. The conversion kit is complete with an axle, adjustment clamp, driveshell, and all driveshell internals for a plug-and-play swap. Micro Spline Driveshell Instructions - Compatible with Shimano Micro Spline cassettes; XTR, XT, and SLX - Compatible with ISO 142x12mm, ISO B 148x12mm, and ISO Superboost DH 157x12mm rear hubs.

Replacement freehub bodies for Vault hubs. - Use to replace worn/damaged freehub body or to switch cassette standards. - 60T

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.

SRAM's Rise 60 conversion caps are the ticket for converting your Rise 60 wheels to a different axle type.

Shimano Dura-Ace 9000 Hub Quick Release Skewer. - Axle Type: Standard QR

- Skewer Trek QR-18 100mm Bolt-On Front Black - Skewer Trek QR-18 135mm Bolt-On Rear Black

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Big Deal spoke nipple washers are not required for tubeless set up. When used, they eliminated the need for tubeless tape.

Who knew we could make a thru axle disappear? The Maxle Stealth offers a light, low profile alternative to Maxle Lite. Features - 34g lighter than Maxle Lite - Easy installation with a 6mm Allen wrench

Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10

Switching to tubeless or in need of valve replacements? Serfas Tire RX replacement valves will do the trick. Available sizes of 32mm, 44mm, or 60mm valves with removable cores, extra valve core, and Schrader to Presta adapter with core removal tool. Please note, Due to the multi-step chemical process and variables involved in anodizing, colors may vary slightly between batches produced.

Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.

To be used exclusively with Bontrager Tubeless Ready (TLR) rims. The rim strips you need to upgrade to Tubeless These rim strips are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Product details - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Use only with appropriate Bontrager TLR rim valve - Rim strip replacement is recommended if removed from the wheel - Sold as singles - White strip is recommended for carbon rims - TLR rim valve sold separately

- Kits include one pair of end caps - Instructions and hub axle determinations are available online @ www.notubes.com

Hub End Caps for Go-Devil Hubs. Caps for quick release, 12mm, and 15mm available.

Rear Thru Axle conversion kit for Go-Devil Hubs - Converts QR to 142x12mm thru (axle not included)

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 135mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 146mm - 1 axle per bag

Secure - Prevents theft instead of standard 9 mm quick-release skewers Quick Assembly - Use proprietary key on frame dropout Construction - Stainless springs with chromoly axle